| Engine Model |
Cat® C9.3 ACERT™ |
| Flywheel Power |
235.0 hp |
| Operating Weight |
56669.0 lb |
| Shipping Weight |
47619.0 lb |
| Gross Power |
252.0 hp |
| Net Power – Caterpillar |
235.0 hp |
| Net Power – ISO 9249 |
235.0 hp |
| Net Power – SAE J1349 |
235.0 hp |
| Net Power – EU 80/1269 |
235.0 hp |
| Bore |
4.5 in |
| Stroke |
5.9 in |
| Displacement |
567.0 in3 |
| Fuel Tank |
108.0 gal |
| Cooling System |
22.5 gal |
| Engine Crankcase |
8.0 gal |
| Power Train |
16.0 gal |
| Final Drives (each) |
9.0 gal |
| Pivot Shaft Compartment |
1.8 gal |
| Hydraulic Tank |
20.0 gal |
| Bulldozer |
4000.0 psi |
| Tilt Cylinder |
4000.0 psi |
| Ripper (Lift) |
4000.0 psi |
| Weight – With One Shank |
3572.0 lb |
| Ripper (Pitch) |
4000.0 psi |
| Tilt Cylinder Flow – Head End Flow |
24.6 gal/min |
| Tilt Cylinder Flow – Rod End Flow |
17.4 gal/min |
| Ramp Angle |
26.0 Degrees |
| Pocket Spacing |
35.4 in |
| Shank Gauge |
70.9 in |
| Installed Weight |
3350.0 lb |
| Winch Length |
43.9 in |
| Overall Width |
43.0 in |
| Throat Clearance |
8.6 in |
| Rope Diameter (recommended) |
1.0 in |
| Maximum Bare Drum Line Pull |
90000.0 lb |
| Maximum Bare Drum Line Speed |
70.0 ft/min |
| Maximum Full Drum Line Pull |
57000.0 lb |
| Maximum Full Drum Line Speed |
116.0 ft/min |
| AC Compressor Nominal Input Voltage |
320.0 volts |
| AC Compressor Maximum Input Current |
12.0 amps |
| Electric Water Pump System Nominal Input Voltage |
320.0 volts |
| Electric Water Pump System Nominal Input Current |
5.0 amps |
| Fuel Tank, High Capacity |
126.0 gal |
| AC Generator and Propulsion Module Voltage |
480.0 volts |
| Gross Power – ISO 14396 |
253.0 hp |
| Pump Output – Steering |
82.4 gal/min |
| Pump Output – Implement |
52.8 gal/min |
| Final Drive (LGP each) |
11.0 gal |
| Shank Section |
72 mm x 228 mm 2.8 in x 9.0 in |
| Type |
Electric Drive |
| Winch Drive |
Hydraulic |
| Cable Ferrule Size (O.D. × Length) |
60 mm x 65 mm 2.38 in x 2.56 in |
| Control |
Electronic/Hydraulic |
| Pump Type |
Piston, Variable Displacement |
| Steering |
5950.0 psi |
| Lift Cylinder Flow |
42.0 gal/min |
| Ripper Cylinder Flow |
42.0 gal/min |
| Winch Model |
PA90 |
| Weight* |
3350.0 lb |
| Oil Capacity |
3.2 gal |
| Winch and Bracket Length |
93.9 in |
| Winch Case – Length |
43.7 in |
| Winch Case – Width |
32.5 in |
| Increased Tractor Length – STD |
93.9 in |
| Increased Tractor Length – LGP |
93.9 in |
| Drum Diameter |
12.5 in |
| Drum Width |
8.9 in |
| Flange Diameter |
24.0 in |
| Drum Capacity – 24 mm (1 in) |
203.0 ft |
| Drum Capacity – 29 mm (1.13 in) |
185.0 ft |
| Ferrule Size (O.D. × Length) |
60 mm x 65 mm 2.38 in x 2.56 in |
| Type |
Multi-Shank |
| Number of Pockets |
3 |
| Overall Beam Width |
82.2 in |
| Beam Cross Section |
355 mm 14.0 in |
| Maximum Clearance Raised (under tip, pinned in bottom hole) |
23.1 in |
| Maximum Penetration |
25.6 in |
| Maximum Penetration Force |
19639.0 lb |
| Pryout Force |
52695.0 lb |
| Weight – Each Additional Shank |
330.0 lb |
| Operating Weight – STD SU |
56669.0 lb |
| Shipping Weight – LGP |
52866.0 lb |
| Operating Weight – LGP S |
62115.0 lb |
| ROPS/FOPS |
SAE 1040, ISO 3471-1994/ISO 3449-2005, SAE 5231 |
| Cab |
ANSI/SAE J1166 OCT 98 |
| Brakes |
ISO 10265 2008 |
| Pressure Setting – Steering |
4000.0 psi |